Current Performance Wiring - Standalone Gen V L83 L86 L8T 8L90E Stocker Series Standalone Harness

Photos of products are sample images. Actual product may vary.

Designed to be a universal fit LTx engine harness for 2014-up L83, L86 and L8T Engines, our Stocker Series harnesses come standard with a sealed fuse box, Techflex split braided loom and heat shielding to protect areas of the harness that are typically near exhaust.

Easily add electric fans with our Sealed E-Fan Add-on Module (Includes PWM module for Fan relay control)

The CPW Stocker series harness contains all of the following connections:

• ECM (J1 Blue, J2 Black, and J3 Gray Connections for factory GM E92 or E92A ECM)
• TCM (Single black 66 pin connector, plugs in to factory GM T87 or T87A transmission computer)
• Transmission (36 pin Latching connector)
• Diagnostic Link Connector (16 pin black, intended to mount inside vehicle for ease of access)
• Pedal (6 pin connector, wired for Corvette pedal p/n 19417903 or equivalent)
  • Easily switch to factory GM truck pedal by swapping brown and white/black wires
• Crank Position Sensor (3 pin black, rear passenger side behind starter. For 58x Crank reluctor)
• Starter (Single pin connector for Gen V starter solenoid)
• Cam position/VVT (8 pin connector, front of engine at bottom of timing cover)
• Knock sensors (2 pin plug on each side of engine)
• MAP sensor (3 pin black plug, sensor mounts to intake in various locations depending on intake)
• Engine coolant temperature (2 pin plug, top of water pump)
• Mass Air Flow (8 pin plug, installed in inlet ducting. Sensor p/n 23262343 or equivalent)
• Injector Sub-harnesses (two 12 pin plugs at rear of intake, one on each injector bank)
• Coils (4 pin connectors, 4 connections on each side of engine, 8 total)
• Throttle Body (6 pin flat plug)
• Oil Pressure (3 pin flat plug, front of engine under throttle body)
• Cylinder Shutoff (DOD/AFM) (5 pin connector, front of engine under throttle body)
• Oxygen Sensors (4 pin flat plug. Routed out back side of engine. Use GM p/n 12659516 or equivalent)
• Alternator (2 pin plug, Connects to stock GM Gen L83/L86 Alternator)
• 2014-2016 Fuel rail pressure sensor connector (4 pin near rear Driver’s side of intake, only used for 2014-2016 engines)
• A/C Pressure (3 pin plug, rear Passenger side of harness. For idle adjustment and e-fan control functions)

Bare input and output wires

• 12V switched (Pink/Black, ignition power signal from vehicle ignition switch)
• Cranking Signal (Yellow/Black, 12V signal to trigger starter relay. Makes use of built in neutral safety of 6 and 8 speed transmissions)
• Power to Fuel Pump (Gray, 20A fused output from fuel pump relay pre-installed in sealed fuse box)
• Tachometer (White, engine speed output from ECM)
• Speedometer (Dk Green/White, calculated vehicle speed output from ECM)
• Check Engine (Brown/White, ground signal from ECM to operate service engine light)
• Fan 1 (Dark Green, control wire from ECM for PWM Fan control or to operate primary electric fan relay)
• Fan 2 (Dark Blue, control wire from ECM to operate secondary electric fan relay)
• Brake Switch (Light Blue, connect to brake switch for TCC lockup control)

Gen V L83 L86 L8T E92 standalone engine harness with 8L90E transmission
Use with MAF sensor p/n 23262343 or equivalent
Use with Oxygen Sensor p/n 12659516 or equivalent
Wired for Corvette pedal p/n 19417903